Licensed & Insured · Locally Owned · Free Inspections Call (210) 504-1295
W Wannamaker Roofing San Antonio's Trusted Roofer
· 7 min read

Starter Strip: Why Cheap Roofers Skip It | Wannamaker

There's a narrow strip of material that runs along the eaves and rakes of your roof — maybe eight inches wide — that most homeowners never think about. It's called starter strip, and it costs roughly $150–$250 in material for an average San Antonio home. That's a rounding error on a $10,000+ roof. But some installers skip it anyway, and the consequences show up during the first serious windstorm when shingles start peeling off your eaves like stickers off a bumper.

What Starter Strip Actually Does

Your standard asphalt shingle has a sealant strip — a line of adhesive that bonds to the shingle above it once the sun heats it up. This creates a sealed, wind-resistant layer across your entire roof deck. But there's a problem at the bottom edge: the first course of shingles has nothing underneath to seal to. Without something there, wind can catch the exposed tabs and lift them.

That's the job of starter strip. It's a narrow shingle (or a pre-cut roll product) installed along the eaves and rakes before the first course goes down. It provides two things:

  • A sealant strip for the first course. The adhesive on the starter bonds to the underside of your first row of shingles, locking them down against wind uplift.
  • A water barrier at the edge. Shingle tabs have cutouts between them. Without starter strip behind those cutouts, water can reach the deck at the most vulnerable part of the roof — right above your fascia and soffit.

Starter strip isn't optional. Every major shingle manufacturer — GAF, Owens Corning, CertainTeed, Atlas — requires it for warranty compliance. Skip it, and you may void the manufacturer's warranty entirely.

Why Some Installers Skip It

The honest answer? It saves time and a small amount of money. On a 30-square roof (about 3,000 square feet), starter strip might cost $150–$250 in material and add 30–45 minutes of labor. For a crew that's trying to knock out two roofs a day at razor-thin margins, those minutes matter.

Here's how the shortcut usually plays out:

  • Flipped shingles. Instead of using actual starter strip, a crew will flip a regular shingle upside down along the eave. This technically provides a backing, but the sealant strip ends up in the wrong position — too high, too low, or facing the wrong direction. The first course never seals properly.
  • Nothing at all. The worst-case scenario. The first course goes directly onto the drip edge and underlayment with no starter behind it. We've seen this on roofs installed less than two years prior during storm damage inspections.
  • Starter on eaves only, skipping rakes. Many installers will put starter along the bottom edge but ignore the sloped edges (rakes). Wind doesn't just come from below — it hits from the sides too, especially on San Antonio homes with gable ends facing prevailing southerly winds.

What Happens When Starter Strip Is Missing

San Antonio averages wind gusts above 50 mph several times per year, and spring storm season regularly delivers gusts over 60 mph. That's more than enough to exploit a missing starter strip.

When the first course isn't sealed down, wind lifts the shingle tabs along the eave. Once one tab lifts, the shingle above it loses its seal too. This cascading failure is why you sometimes see entire sections of shingles peeled off a roof after a storm — starting from the bottom edge and working upward.

The damage isn't always dramatic. Sometimes it's subtle: lifted tabs that don't lay flat, small leaks at the fascia line, or shingles that develop cracks along the nail line because they've been flexing in the wind for months. By the time you notice, water may have already reached the deck.

And here's the kicker: if your insurance claim adjuster determines that shingle blow-off was caused by improper installation rather than storm damage, your claim gets denied. We've watched it happen.

How to Check if Your Roof Has Starter Strip

You can do a basic check from the ground with binoculars. Look at the bottom edge of your roof along the eaves:

  • Look for a uniform, smooth edge. Properly installed starter strip creates a clean line at the eave. If you see shingle tab cutouts visible at the very bottom row, that's a red flag — it means there's no backing behind those gaps.
  • Check shingle alignment. The first course should overhang the drip edge by about ½ to ¾ inch. If shingles are flush with or behind the drip edge, something went wrong during installation.
  • Feel the tabs (safely). If you can access your eave from a ladder, gently press the bottom edge of the first-course shingles. They should feel firmly adhered. If they lift easily, the starter strip is either missing or its sealant never activated.

If anything looks off, schedule a free roof inspection and have a professional confirm what's underneath.

The Bigger Picture: Installation Quality Over Material Brand

Starter strip is just one example of a broader truth: the quality of your roof depends far more on installation than on the shingle brand printed on the wrapper. You can put the best architectural shingles money can buy on a roof, but if the crew skips starter strip, uses too few nails, places nails too high, or ignores the manufacturer's installation specs, that premium shingle will fail.

When we quote a roof replacement cost in San Antonio, the price includes every component the manufacturer requires — starter strip, proper nail placement, ice and water shield where needed, correct ventilation. That's not upselling. That's the baseline for a roof that actually performs.

The same principle applies across roofing types. Whether we're installing metal roofing, tile roofing, or standard asphalt, every system has non-negotiable details that separate a 25-year roof from a 5-year headache.

What to Ask Your Roofer Before They Start

If you're getting quotes for a new roof in San Antonio, Stone Oak, Helotes, or anywhere in the Hill Country, ask these questions:

  • "Are you installing manufacturer-specific starter strip?" The answer should be yes, not "we flip a shingle."
  • "Will you install starter on both eaves and rakes?" Both edges need protection.
  • "Can I see the installation spec sheet for the shingle you're using?" Every manufacturer publishes one. A contractor who follows it won't hesitate to share it.
  • "Is your installation eligible for the manufacturer's system warranty?" System warranties (like GAF's Golden Pledge or Owens Corning's Platinum Protection) require certified installation — which always includes proper starter strip.

Not Sure What's Under Your First Course?

If your roof was installed by a previous contractor and you're not confident it was done right, we'll check for you. Wannamaker Roofing offers a free roof inspection that covers starter strip, nail placement, flashing, ventilation, and every other detail that separates a proper installation from a liability. No pressure, no obligation — just an honest assessment from a local crew that's been doing this in San Antonio since 2012.

Starter strip costs less than a decent dinner out. Replacing the shingles that blew off because it was skipped costs thousands. If you take one thing from this article, let it be this: the cheapest bid isn't the cheapest roof. The cheapest roof is the one that doesn't fail.

Ready for a straight answer on your roof?

Free, no-pressure inspection with photo-documented findings. Most inspections done within 48 hours.